Click HERE to Order this kit.

Power Lock and Keyless Entry Installation instructions: Bronco Ranger

Door Lock Actuator Installation:


Remove the door panels.They are held on by screws and joints that will pop out.


Start by pulling on the bottom of the door, unpopping all the joints.Then lift up on the panel, and it should come right off.

Remove the plastic on the inside of the door.Be careful, because you will be reusing the plastic.


Drill the holes to mount the actuator.The position of the actuator is shown above in the middle picture.It is mounted vertically and only the top of the strap and actuator are visible in the picture.

Install the piece that attaches to the power lock rod to the manual lock rod and make sure that everything is moving freely. (see above right picture)You will probably have to bend the rod to get it to match up.

Do not reassemble door until after you have tested the system.


Wiring Installation:


Install the keyless entry kit and relays under the dash in the vicinity of the steering wheel.You can install it wherever you want, but it may be easiest to install under the steering wheel.

Hook the positive wires to a positive source that is always on.The radio is a good source for this.††

Run the Actuator Wiring to the doors.These are the red and black wires in the gray sleeve.Donít try to get it through the door, yet.

On the Ranger that I installed the power locks on, there were no previous wires going to the doors.On these cars you will have to drill holes in the car frame and door and run the wires that way.If your car has wires running to the doors, the below instructions should apply.

Running the wires to the doors is done in two steps.First of all unsnap the black rubber wire tube from the frame side of the car.There should be wires inside.

The first step is to get the wires going from inside the car out to the opening by the door.The above middle picture shows the inside view of the hole you are aiming for.††† Remove the glove compartment.This should unscrew, and then you will carefully remove it.

Using the conduit, snake the conduit up and out the opening by the door.This is done starting from underneath the dashboard.Then when you can grab the conduit through the frame opening by the door, tape the wires to the conduit, and pull the conduit and the wires through the opening.

Starting from inside the door, snake the conduit through the rubber tube and out the top of the rubber tube.Then tape the wires to the conduit and pull the conduit back through.


Hook the wires actuator wires up to the actuator, compress them lightly with some pliers, to make sure that they stay attached, and then tape them up, to prevent the metal from contacting other metal and shorting anything out.

Repeat the procedure with the driverís side.You may have to unbolt the fuse box.


Note:When you are testing the lock/unlock functions, it may be necessary to reverse the lock actuator wires to get lock and unlock to work correctly (instead of backwards).


Instructions For Push Button On and Off Buttons:The buttons should be wired into the Black wires coming out of the relays.Find a suitable place to mount the buttons, drill holes and install.The other wire coming out of the buttons is wired into ground (-).






















Wiring Diagram for Keyless Entry Kit:


††††††††††††††††††††††††††††††††††††††††††††††† †††††††† +12V

††††††††††††††††††††††††††††††††††††††††††††††††††††††††††† Red


††††††††††††††††††††††† ††††† Red†††††††††††††††††††††††††††††††††††††††††††††† White







Keyless Entry

††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††† ††††††† Yellow††††††††††††††††

††††††††††††††††††††††††††††††††††† ††††

††††††††††††††††††††††††††††††††††† †††† Blue/Black †††††††††††††† Black†††††††††††††††††††††††††††††††††† Optional Lock/Unlock

††††††††††††††††††††††††††††††††††† †††† ††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††† Buttons


††††††††††††††††††††††††††††††††††† ††††† Green / Black†††††† †† Black†††††††††††††††††††††† †††††††††††† Join Buttons to Black Ė Blue/Black

††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††† And Black - †††††††††† Blue/Black Wires

††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††† †††

††††††††††††††††††††††††††††††††††† †††† Black†††††††††††††††††††† †††† Red†††††††††††††††††††††††††††††††††††

††††††††††††††††††††††††††††††††††† †††† Violet/Black††††††††† †††† Red




†††††††††††††† ††††††††††††††††††††††††††††††††††††††††††††To Neg (-)††††††††††††††††††† Blue

White/Red††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††† ††††††† Blue


(to Power Trunk)


Lock Motor


††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††† Green††††††††† Red


††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††† Blue†††††††††††† Black

Power Trunk Relay





††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††† †† Red ( +12v)†††††††††††††††††††††††





†††††† Black†††††††††††††††††††††††††††††††††††††††††††† Yellow


††††††††††††††††††††††††††††††††††††††††††††††††††††††††††††† White


††††††††††††††† Blue




†††††††† Black (to Neg)